TL;DR: Installing the Pentair IC15 IntelliChlor salt chlorinator cell takes 2–3 hours and requires basic plumbing and electrical skills. This salt cell automatically produces chlorine from dissolved salt, eliminating manual chlorine addition and providing consistent sanitization. Proper installation ensures optimal chlorine production, extends cell life, and maintains crystal-clear water. Professional installation recommended for electrical connections.
SEO Summary: This 2026 guide provides complete step-by-step instructions for installing Pentair IC15 IntelliChlor salt chlorinator including plumbing, wiring, salt addition, and system startup procedures.
Related Categories
Table of Contents
Product Overview and Function
The Pentair IC15 IntelliChlor is a salt chlorinator cell that automatically produces chlorine from dissolved salt in pool water.
Product Description:
- Part Number: Pentair IC15
- Type: Salt chlorine generator cell
- Capacity: Up to 15,000 gallons
- Production: 0.60 pounds chlorine per day
- Cell Life: 10,000 hours typical (3–5 years)
- Power: 120/240V AC (low voltage operation)
Function and Purpose:
- Converts dissolved salt to chlorine through electrolysis
- Automatically sanitizes pool water
- Eliminates manual chlorine addition
- Provides consistent chlorine levels
- Reduces chlorine odor and irritation
- Softer water feel compared to traditional chlorine
System Components:
- Salt cell (electrolytic chamber)
- Power supply/control unit
- Flow switch (detects water flow)
- Mounting unions and hardware
- Electrical connections
- Display panel for monitoring
Benefits of Salt Chlorination:
- Automated chlorine production (set and forget)
- Lower operating costs (salt vs. chlorine)
- Reduced chemical handling
- Softer, more comfortable water
- Less eye and skin irritation
- Consistent sanitization levels
- Environmentally friendly operation
Planning and Requirements
Proper planning ensures successful installation and optimal performance.
Pool Size Verification:
- IC15 rated for pools up to 15,000 gallons
- Measure pool volume accurately
- Consider upgrading to IC20 for pools up to 20,000 gallons
- Or IC40 for pools up to 40,000 gallons
- Oversizing provides reserve capacity
Location Selection:
- Install after filter, before heater (if present)
- Minimum 12 inches straight pipe after filter
- Horizontal or vertical installation acceptable
- Accessible location for service
- Protected from direct sunlight when possible
- Near power source for control unit
Plumbing Requirements:
- 2-inch PVC plumbing (standard)
- Adequate straight pipe for proper flow
- Flow rate: 25–75 GPM optimal
- Minimum 15 GPM required
- Bypass valve recommended (for service)
- Unions for easy cell removal
Electrical Requirements:
- Dedicated 120V or 240V circuit
- GFCI protection required
- Proper bonding per NEC Article 680
- Adequate wire gauge for distance
- Conduit for wire protection
- Junction box for connections
Tools and Materials Needed
Proper tools ensure efficient installation.
Required Tools:
- Hacksaw or PVC pipe cutter
- Measuring tape
- Sandpaper or deburring tool
- Adjustable wrench
- Screwdrivers (Phillips and flathead)
- Wire strippers and cutters
- Multimeter (for electrical testing)
- Drill with bits (for mounting)
- Level
- Safety glasses and gloves
Required Materials:
- Pentair IC15 IntelliChlor salt cell system
- PVC primer and cement
- 2-inch PVC pipe (as needed)
- PVC fittings (elbows, tees, unions)
- Electrical wire (14–12 gauge)
- Wire nuts and connectors
- Conduit and fittings
- Pool salt (sodium chloride)
- Teflon tape
Optional But Recommended:
- Bypass valve assembly
- Flow meter for monitoring
- Pressure gauge
- Salt test kit or strips
- Quality IC15 IntelliChlor cells for above-ground pools
- Backup IC15 generators for replacement
Preparation and Safety
Proper preparation prevents mistakes and ensures safe installation.
System Shutdown:
- Turn off pool pump at breaker
- Close isolation valves if available
- Drain water from installation area
- Verify all power disconnected
- Wait for system to fully depressurize
Planning Layout:
- Measure plumbing configuration
- Determine cell orientation and position
- Plan pipe cuts and fitting requirements
- Sketch plumbing layout with measurements
- Identify power supply routing
- Verify adequate space for cell and control unit
Workspace Preparation:
- Clear area around installation location
- Ensure adequate lighting
- Have all tools and materials ready
- Protect surrounding areas from PVC cement
- Ensure stable footing and access
Safety Considerations:
- Wear safety glasses (protect from PVC cement fumes)
- Work in well-ventilated area
- Avoid skin contact with PVC cement
- Follow NEC requirements for electrical work
- Keep children and pets away
- Have fire extinguisher nearby
Plumbing Installation
Proper plumbing ensures optimal water flow and cell performance.
Pipe Preparation:
- Measure and mark pipe cut locations
- Cut pipes square and perpendicular
- Deburr all cut ends with sandpaper
- Test-fit cell and unions before gluing
- Verify cell orientation correct
- Ensure adequate clearance for service
Union Installation:
- Install union on each side of cell
- Apply PVC primer to pipe ends and union sockets
- Apply PVC cement to both surfaces
- Insert pipe into union with twisting motion
- Hold for 30 seconds to ensure bond
- Wipe excess cement immediately
- Allow 2 hours minimum before pressure testing
Cell Mounting:
- Thread cell into unions hand-tight
- Ensure flow direction arrow points correct way
- Tighten union nuts with wrench (don't over-tighten)
- Verify cell level and properly aligned
- Check that cell secure and cannot move
- Ensure adequate clearance for cable connections
Bypass Valve (Optional but Recommended):
- Install 3-valve bypass assembly
- Allows cell isolation for service
- Enables flow adjustment if needed
- Facilitates cell removal without draining system
- Provides flexibility for maintenance
Electrical Wiring
Proper wiring ensures safe, reliable operation.
Power Supply Installation:
- Mount power supply/control unit near cell
- Protected location (weatherproof if outdoors)
- Accessible for operation and service
- Secure mounting with provided hardware
- Verify level and properly oriented
Power Wiring:
- Run power wire from breaker panel to power supply
- Use proper wire gauge (14 or 12 gauge typical)
- Install in conduit per code requirements
- Connect to dedicated GFCI-protected circuit
- Verify correct voltage (120V or 240V)
- Tighten all terminal connections securely
Cell Wiring:
- Connect cell cable to power supply
- Route cable through conduit if required
- Secure cable with clips or ties
- Avoid sharp bends or kinks
- Keep cable away from hot surfaces
- Verify connections tight and secure
Flow Switch Installation:
- Install flow switch in plumbing (if not integrated)
- Connect flow switch wires to power supply
- Verify proper orientation and position
- Test flow switch operation
- Ensure proper water flow detection
Bonding:
- Connect bonding wire to cell bonding lug
- Bond to pool bonding grid per NEC Article 680
- Verify proper grounding of power supply
- Test ground continuity with multimeter
- Ensure all connections tight and corrosion-free
Salt Addition and Startup
Proper salt level is critical for chlorine production.
Salt Requirements:
- Target salt level: 3200 PPM (parts per million)
- Acceptable range: 2700–3400 PPM
- Use pure pool salt (sodium chloride, NaCl)
- Avoid salt with additives or anti-caking agents
- Calculate salt needed based on pool volume
- Use quality salt system start products for initial setup
Salt Calculation:
- Formula: (Desired PPM - Current PPM) × Pool Gallons ÷ 1,000,000 × 8.35
- Example: 15,000 gallon pool needs approximately 400 pounds salt
- Start with 80% of calculated amount
- Test and add more if needed
- Easier to add salt than remove it
Salt Addition Procedure:
- Add salt directly to pool (not through skimmer)
- Distribute salt around pool perimeter
- Brush salt to help dissolve
- Run pump for 24 hours to fully dissolve and circulate
- Do NOT turn on salt cell yet
- Wait for salt to completely dissolve
System Startup:
- After 24 hours, test salt level
- Adjust salt if needed to reach 3200 PPM
- Restore power to salt cell system
- Turn on power supply
- Set chlorine output level (start at 50%)
- Verify cell producing chlorine (check display)
- Monitor chlorine levels daily for first week
Operation and Maintenance
Proper operation and maintenance ensure long cell life.
Daily Operation:
- System operates automatically when pump running
- Produces chlorine based on output setting
- Monitor salt level monthly
- Test chlorine levels 2–3 times weekly
- Adjust output setting as needed
- Check display for alerts or errors
Chlorine Output Adjustment:
- Increase output if chlorine too low
- Decrease output if chlorine too high
- Typical range: 30–70% output
- Adjust seasonally (higher in summer)
- Balance with pool usage and temperature
Cell Cleaning:
- Inspect cell every 3 months
- Clean when calcium buildup visible
- Remove cell from plumbing (use unions)
- Flush with garden hose
- Soak in diluted muriatic acid if needed (1 part acid to 4 parts water)
- Rinse thoroughly before reinstalling
- Never use metal tools on cell plates
Water Chemistry:
- Maintain pH: 7.2–7.6
- Maintain alkalinity: 80–120 PPM
- Maintain calcium hardness: 200–400 PPM
- Maintain salt: 3200 PPM (2700–3400 range)
- Balance chemistry weekly
- Use salt water magic products for water quality
Winterization:
- Remove cell and store indoors
- Clean cell before storage
- Store in dry, protected location
- Disconnect power supply
- Protect plumbing from freezing
Troubleshooting Common Issues
Addressing problems ensures reliable chlorine production.
No Chlorine Production:
- Cause: Low salt level
- Solution: Test salt, add to reach 3200 PPM
- Cause: Cell dirty or scaled
- Solution: Clean cell per maintenance procedure
- Cause: No power to cell
- Solution: Check breaker, verify wiring connections
- Cause: Cell end of life
- Solution: Replace cell
Low Chlorine Production:
- Cause: Output setting too low
- Solution: Increase output percentage
- Cause: Insufficient run time
- Solution: Run pump longer (8–12 hours minimum)
- Cause: High chlorine demand (heavy use, hot weather)
- Solution: Increase output, supplement with shock if needed
High Salt Warning:
- Cause: Salt level too high (over 3400 PPM)
- Solution: Dilute by draining and refilling with fresh water
- Cause: Faulty salt sensor
- Solution: Test salt manually, calibrate or replace sensor
Flow Error:
- Cause: Insufficient water flow
- Solution: Clean filter, check pump operation
- Cause: Faulty flow switch
- Solution: Test and replace flow switch if needed
- Cause: Air in system
- Solution: Bleed air from system, check for leaks
Conclusion and Key Takeaways
Installing the Pentair IC15 IntelliChlor salt chlorinator takes 2–3 hours and provides automated chlorine production for pools up to 15,000 gallons. Proper installation with correct plumbing, wiring, and salt levels ensures years of reliable, hands-free pool sanitization with softer, more comfortable water.
Essential Takeaways:
- IC15 produces chlorine from salt for pools up to 15,000 gallons
- Install after filter, before heater in return line
- Requires 2-inch plumbing with adequate flow (25–75 GPM)
- Dedicated GFCI-protected electrical circuit required
- Turn off power before starting installation
- Install unions on both sides for easy cell removal
- Ensure flow direction arrow points correct way
- Mount power supply in protected, accessible location
- Connect and bond all electrical per NEC Article 680
- Add salt to achieve 3200 PPM (approximately 400 lbs for 15,000 gallons)
- Run pump 24 hours to dissolve salt before activating cell
- Start at 50% output and adjust based on chlorine levels
- Clean cell every 3 months or when scaled
- Maintain proper water chemistry for optimal performance
- Remove and store cell indoors during winter
- Upgrade to larger salt cells for bigger pools
- Use salt support system start products
- Maintain with IC60 cells for commercial applications
- Salt chlorination saves $300–$600 annually vs. traditional chlorine
- Shop quality salt system parts from our pool parts collection
Follow these installation steps systematically for professional-quality results. Proper salt chlorinator installation provides years of automated, cost-effective pool sanitization with superior water quality and reduced chemical handling. The investment in salt chlorination pays dividends in convenience, comfort, and long-term savings.
